From: treon3verdery@gmail.com   
      
   🌳🌳🌲🌳🌳🌳🧠🌳🌳🌳🌳🌳🌳🌳🌳🌳🌳🌳   
      
   ompanysreitsstyles of happiness   
      
   Really ignorant airplane form, when a person throws a peper towel tube that   
   isnt spinning i think it doesnr go very far, an aircraft that is mostly just a   
   spinning tube could fly and stay up if it spins with like battery inductive   
   photonic or nuclear    
   power energy, it would have a big extrenal very annular or helical light gear   
   track and independently tlobed that is big stick out custom angleable form   
   half propellor shapes would just out of it, the moving cassetes each   
   adjustable lobe was on would    
   shuttle around the some huge sized central aperture of the rolling   
   counterclockwise paper towel tube, increasing its lift it would be covered   
   with whatever kind of raised nubs, perhaps like drinking straw gradual helix   
   lines causing aerodynamic lift as    
   it angle-lever-rotates through the air, although imaginably these helix nubs   
   as small as velvet or corduroy fabric they could just as easily be a few   
   thousand reversibly fastener attached 8-11 inch contour fins looking a little   
   like washing machine    
   agitator single rays;the tube covering helical lumps, notably the 8-11 inch   
   rays, could be under computer dynamic control to angle certain ways   
   individually to produce variously the most upward lift, the specific vertical   
   take off and landing push    
   earthward airflow pattern, the annulus big circle propellor cassettes move on   
   an em motion track, each functions independently under computer control and   
   can be replaced as individual cassettes if they wear out, the dynmaic computer   
   directed form half    
   propeller annulus has lift sufficient to get the aircraft airborne and then   
   the directional vector power they provide and the lift they provide is   
   complemented and likely exceeded by the all along tube helical nubs,   
   manufacturability and transportability    
   of airplane parts could be very cheap because the paper towel tube can   
   actually be 8 or 4 snap/bolt together quarter or eighth segments of the   
   assemblable tube, and can be of standard 40 foot truck shipping container   
   length, a likely material is aluminum    
   or polymer, perhaps laser peened for added strength, the 1/2 propellors on   
   linear actuator cassetes could likely easily fit in 40 foot containers as   
   well, assemblers of the airplane could use what is previously described as   
   autoreticule interferometry    
   paint and camera/lidar workpiece reading tools, robots, or handtools, that can   
   tighten and and immobilize bolts to 1/4 wave precision with full   
   interferometry view of the aircraft's entire length supporting minimal   
   structure stress points of all kinds.    
   Notably the entire exterior of the aircraft rotates to produce lift and   
   direction vector, the interior cargo/passenger area has tubular sheath   
   rotating around it. One possible advantage of a tubular sheath all vehicle   
   airfoil is perhaps double digit    
   energy savings over wing and engine airplanes, that is because i read a tall   
   tubular entire surface rotates wind electricity maker is much more efficient   
   than just a big tripropeller on a pylon. This is described as an airplane, but   
   it can be built small    
   like a drone and it possible greater micromaneuverability and unknown energy   
   efficiency may be advantageous, it looks completely different than 6 and 8   
   propellor drones, big diameters of tube bring 4/3 pi R^3 rapid expansion of   
   cargo or airdrop water or    
   extinguisher chemicals, cloud seeding, agricultural uses, or passengers, air   
   cargo, one could be a scramjet or ramjetglider solar   
   Dental technology, laser attracts leukocytes to gum diseasey curing it,   
   probiotic makes same tooth build up chemicals as saliva, only greater amounts   
   khlp + gum disease and plaque bacteria chemicals, teething comfort producers,   
   removing all nociception    
   permits double nerve mass at teeth of all species   
   Mammalp and nonmammals   
      
   Live application during use laser peening of ball bearings and other bearings   
   and raceway bearings is i think possible, camera, lidar, 10-30 micrometer   
   ultrasound, thz or rf backscatter imaging such as interferometry of live   
   bearings at live applications    
   show a guiding computer where bearings are getting anisotrpoic lopsided wear,   
   noting that a computer guides in situ laser peening of the bearing or other   
   moving part such that wear patterns, simply from wearing less is both highly   
   homogenous and also    
   wear is minimized, something like minute but bright SMD 1/4 mm laser diodes   
   possibly inductively powered or photovoltaic concentrator powered or THz   
   powered or briefly introduced vibrations that make piezoelectric power powered   
   laser diodes could laser    
   peen live at the bearing, ball bearing, raceway or other moving part, notably   
   without a wiring pathway to the bearing or moving padt area, laser peening to   
   produce highly homogenous wear extends the lifetime of the bearings and moving   
   parts,    
      
      
   [continued in next message]   
      
   --- SoupGate-Win32 v1.05   
    * Origin: you cannot sedate... all the things you hate (1:229/2)